IGM Silicone Glue Applicator Roller Kit – Ø 20 mm, 47 mm width, grooves for even distribution, with choice of Titebond glue
The IGM silicone glue applicator roller is an accessory for hobby-professional use, made up of a Ø 20 mm silicone roller, 47 mm wide, with angled grooves that hold the glue and ensure even distribution without excess, plus a silicone tray with front notches for collecting excess glue. The design with no protruding parts allows application right up to the edge of the workpiece without damaging the material. Available as a combo with a choice of Titebond glue: Original D2, II Premium D3 or III Ultimate D4. Distributed in Italy by Krollit, official IGM and Titebond distributor since 2007.
- Roller diameter: Ø 20 mm
- Roller width: 47 mm
- Angled grooves: hold glue on the roller, reduce dripping
- Edge application: design with no protruding parts
- Silicone tray with front notches: collects excess glue and rests the roller
- Roller and tray material: silicone
- Cleaning: warm water or dry peeling
- Glue included: choice of Titebond (selectable variant)
Which Titebond glue to choose for your use
The combo is available with three Titebond glue variants. The choice depends on the environment of use and the required level of water resistance.
| Glue | EN 204 class | Use | Open time | Min. application temp. | When to choose it |
|---|
| Titebond Original | D2 | Indoor only | max 5 min | 10°C | Indoor woodworking, furniture, stairs, parquet: high initial tack, fast clamping, yellow colour after drying |
| Titebond II Premium | D3 | Indoor and outdoor | max 5 min | 13°C | Windows and doors, outdoor furniture, structures exposed to occasional moisture: the only single-colour D3 glue certified to EN 204, compatible with RF and hot-press systems |
| Titebond III Ultimate | D4 | Indoor and outdoor | max 10 min | 8°C | Prolonged water exposure, cutting boards and food-contact items, outdoor construction work: resistant to mould, solvents and heat, applicable at low temperatures |
Who this kit is for
| Profile | Fit | Reason |
|---|
| Woodworker gluing large surfaces (panels, side panels, worktops) | Suitable | The 47 mm width and angled grooves spread glue in an even layer over flat surfaces in a single pass, cutting spreading time compared to a flat brush |
| Hobbyist doing veneering or panel assembly work | Suitable | The design with no protruding parts allows application right up to the panel edge without leaving uncovered areas or damaging the material; the tray limits waste on small glue quantities |
| Application in holes, deep mortises or narrow grooves | Not suitable | The Ø 20 mm diameter and 47 mm width make the roller suited to flat, wide surfaces; for cylindrical holes, mortises and narrow grooves, the IGM point applicator kit is the correct tool |
Not suitable for: applying expanding polyurethane glues, two-component epoxy glues or solvent-based contact adhesives, for which cleaning the silicone roller with water is not practical.
Technical specifications
IGM roller kit
| Roller diameter | Ø 20 mm |
| Roller width | 47 mm |
| Grooves | Angled, to hold glue and reduce dripping |
| Edge application | Yes (design with no protruding parts) |
| Tray | Silicone with front notches for glue collection |
| Roller and tray material | Silicone |
| Cleaning | Warm water or dry peeling after drying |
Titebond Original – technical parameters (D2)
| Type | Aliphatic resin in water dispersion |
| Water resistance class | D2 (EN 204) |
| Use | Indoor only |
| Colour after drying | Yellow |
| Open time | max 5 min |
| Assembly time | 10-15 min |
| Full cure time | 24 hours |
| Operating and storage temperature | 10-24°C |
| Water dilutable | Yes, up to 5% |
Titebond II Premium – technical parameters (D3)
| Type | PVA glue in dispersion |
| Water resistance class | D3 (EN 204) |
| Use | Indoor and outdoor |
| Colour after drying | Yellow/orange |
| Open time | max 5 min |
| Assembly time | 10-15 min |
| Full cure time | 24 hours |
| Operating and storage temperature | 13-24°C |
| RF / hot-press compatibility | Yes |
Titebond III Ultimate – technical parameters (D4)
| Type | Advanced proprietary polymer |
| Water resistance class | D4 (EN 204) |
| Use | Indoor and outdoor |
| Colour after drying | Light brown |
| Open time | max 10 min |
| Assembly time | 20-25 min |
| Full cure time | 24 hours |
| Operating and storage temperature | 8-24°C |
| Food-contact safe | Yes (cutting boards and similar items) |
Standard equipment
- 1 silicone roller, Ø 20 mm, 47 mm width
- 1 silicone tray with front notches
- 1 bottle of Titebond glue (choice of variant: Original D2, II Premium D3, III Ultimate D4)
Frequently asked questions
What's the difference between the IGM roller and the IGM brush kit for glue application?
The roller is designed for large, flat surfaces such as panels, side panels and worktops; the brushes in the IGM kit suit narrower surfaces, open mortises and dovetail joints where the roller can't reach.
For veneering or panel gluing in a single pass, the 47 mm roller is faster and spreads a more even layer than a brush. For mixed applications, those working on both large surfaces and profiled joints benefit from having both tools available.
