To join two pieces of wood without screws, you can glue their edges, use dowels or biscuits, or cut an interlocking joint. Choose according to the way the parts meet: widening a panel with adjacent boards is different from making a right-angle frame. If the furniture needs to come apart, choose a demountable connection before applying glue.
This guide covers small woodworking projects and furniture assembly. It does not size connections for beams, roofs or other structural elements.
Which screw-free joint should you choose?
First decide whether you want to widen a panel, make a corner or extend a piece. Check which surfaces will touch and whether the assembly should be permanent.
| Method | Typical use | Check first |
|---|---|---|
| 1. Edge gluing | Boards side by side to form a panel | Straight, matching edges and continuous contact |
| 2. Dowels and glue | Parts with corresponding drilled holes | Hole position, diameter and depth |
| 3. Biscuits and glue | Aligning boards or panels | Slots compatible with the biscuit |
| 4. Mortise and tenon | Rails and stiles in frames | Joint geometry and the part’s function |
The diagrams explain the connections; they are not dimensioned plans or load ratings.
What about joining boards end to end?
Extending a piece by joining its ends is different from gluing long edges. Design the joint to provide suitable bonding surfaces and withstand the intended loads: a “stronger” glue alone is not the answer. The Forest Products Laboratory Wood Handbook describes shaped joints, dowels and tenons that bring long-grain surfaces together. Do not transfer a small furniture joint directly to a structural beam.
How to edge-glue two boards without screws
Prepare the edges, dry-fit the boards, spread the glue and clamp across the joint. Dowels or biscuits can help with alignment, but they cannot correct curved edges or poorly fitting surfaces.
Prepare a stable work surface, straightedge, pencil, clamps with protective pads and an adhesive suitable for the wood and service conditions. Set everything out before opening the glue.
- Check the fit without glue. Place the boards in their final order. If a clear gap remains or closing it requires bending the pieces, correct the machining. WOOD Magazine’s edge-gluing demonstration explains why continuous contact matters more than adding extra adhesive.
- Mark the position. Add reference marks to the faces and rehearse the clamp arrangement. Check that the panel stays flat and the jaws leave room for inspection.
- Prepare the surfaces. Remove dust and residue. Do not glue over a finish without checking adhesive compatibility. If starting with rough boards, plane the wood before assembly.
- Apply glue and assemble. Follow the chosen adhesive’s application instructions and close the joint within its assembly time. PVA wood glue is not a filler for an open joint.
- Clamp and check again. Tighten progressively and distribute pressure along the workpiece. Check for a step between the boards and for bowing. Excessive force cannot replace accurate preparation.
- Wait before machining or loading. Clamp time and time before stressing the joint are different. For most of its wood glues, Titebond advises waiting at least 24 hours before stressing a new joint: consult its manufacturer FAQs and the specific product instructions.

Dowels, biscuits and mortise-and-tenon joints
Dowels: accurate holes matter
Dowels fit into matching holes in the two parts. Use a suitable jig and reference both pieces from the same face. Control drilling depth with a stop and test on scrap of the same thickness to avoid breaking through the visible face.
Dowel diameter, length and number depend on the connection; there is no universal size for every piece of furniture. WOOD Magazine’s dowel-joint procedure shows marking and jig use. Check the fit before gluing without forcing misaligned pieces.
Biscuits: routed slots and alignment
Wooden biscuits fit into slots cut with a biscuit joiner, not ordinary drilled holes. Lamello’s wooden biscuits help align parts while allowing lateral adjustment in the slots. Joint strength also depends on the adhesive. Match biscuit size and cutting depth to the actual material thickness.
Mortise and tenon: joining a frame
The tenon projects into a mortise cut in the other part. It is a joint to consider for rails and stiles, with dimensions chosen for the project. Check the shoulders, fit and squareness before gluing. Glue will not make an excessively loose joint precise, while an overly tight fit can prevent closure or damage the wood.
Which wood glue should you use?
Choose by material, moisture exposure and the time needed for assembly. Products carrying the same brand name do not necessarily have the same uses. These two Krollit products serve different conditions.
Titebond White Glue: indoor work

A PVAc adhesive for indoor use. The White Glue technical sheet excludes outdoor applications, likely moisture exposure and structural load-bearing uses. Do not choose it for a project exposed to rain.
Titebond III Ultimate: also for outdoors

The manufacturer specifies indoor and outdoor use and compliance with the ANSI/HPVA Type I water-resistance test. The III Ultimate technical sheet excludes continuous immersion and structural load-bearing applications. Water resistance does not establish a joint’s load capacity.
For other adhesives, see our wood glue comparison. Always check the instructions on the container you will use.
Mistakes to avoid
- Gluing poorly fitting parts: correct the fit rather than adding glue and pressure.
- Confusing glued with removable: glued dowels and biscuits are not intended for repeated dismantling.
- Leaving glue on a face to be stained: residue can block stain absorption. Protect adjacent areas and follow Titebond’s application advice.
- Extrapolating from a small test piece: a successful sample does not certify furniture or structural load capacity.
Questions about joining wood without screws
Can I join two boards with glue alone?
Yes, for a panel made from boards joined along correctly prepared edges with a suitable adhesive. That does not mean glue alone suits every end joint or load.
Can I join wood without screws or glue?
You need a connection designed to lock mechanically, such as an appropriately designed wedged joint or demountable connector. Simply inserting one piece into another does not secure it in every direction. Check whether the chosen hardware itself needs screws for installation.
Are dowels stronger than biscuits?
There is no universal answer. Geometry, material, size, adhesive and load direction all matter. Select for the actual connection rather than assigning a fixed load capacity to a dowel or biscuit.
Can I skip the clamps?
Not when the adhesive requires clamping. Contact and alignment must be maintained for the specified time; holding the parts by hand briefly is not equivalent.
Is a pocket-hole joint screw-free?
No. A pocket hole hides or angles a screw; it remains a screwed connection. See how to join wood with screws if that suits your project.
Start here: dry-fit the edges for an edge-glued panel, or test your chosen frame joint on scrap. Then prepare the glue, clamps and assembly sequence.
By Sandra Gaspar. Original diagrams by Krollit. Technical references are linked in the text.
